Follow the prompts to clean cylinders Brother printers with the steps below here.
Brother Laser printers have good performance, we have always stressed how compact it is these printers, plus printers Brother brand are well positioned in our list of the best brands of printers.
They are independent printers cylinder unit to the toner cartridge, usually the cylinder of these printers can yield three toner cartridges before changing the cylinder with a new one.
With the passage of time and if we filled our toner several times we may begin to get a bad quality in our printed documents.
The symptom that more is when it is time for you to clean cylinder Brother printers are spots throughout the site, stains like if I opened fallen toner on the page, drops on all sides dust damaging the image of the document we want to print.
Do not worry, it is recommended to go buy a new cylinder, both the manufacturer and I will do the same recommendation, after cylinder begin submitting these problems is difficult for us to continue to receive the same quality when printing.
It may be the case that the unit cylinder is not damaged completely, if we see that the pages even the last to leave has good quality and filled our needs, then it is time to clean the cylinder and save the money we would need to buy a new cylinder.
Then a process for cleaning, may change in a few steps with the cylinder that you have but are very similar, so we need a little cleaning up, clip, pliers and screwdriver.
The cylinder has a very fragile surface is easily damaged and recommend to treat it with care and patience to avoid damaging any stripe is made in the cylinder will show on all pages to be printed on. Do not clean the drum unit with sun exposure, this is damaged without remedies.
First thing we do is loosen the toner drum unit, as mentioned above, the cylinder unit is independent Brother printers, we will release the toner off the drum to start cleaning.
When we started the cylinder cleaning alone, we need to put the drum unit where the cylinder (red or green part) are not maltreated.
We removed a grip that has the drive cylinder at one end, with this we seek the ease of removing the cylinder to expose the toner tank damaged.
The deposit tone damaged, is an amount of powder used to print that does not stick to the paper, this is called toner tank damaged because no use for reuse, as it passes to the deposition of damaged toner is mixed with pieces of paper and dust taken from the environment where the printer is if we again get very pale toner pages without quality.
After removing the handle holding the through going from one extreme to another holding the cylinder, the following is out completely, we seek to remove and leave to weather that is easy to remove the cylinder, remember to be careful, if dropped to the floor or at the same table may be damaged, scratched and this will forever or replace it with a new one.
We now proceed to disassemble and clean everything is the deposit toner damaged, if we have a vacuum cleaner is better, it is advisable to cover us all are of the airways, avoid dust from our bodies that can cause breathing problems even allergies.
We removed everything very carefully checking where each piece goes, we voted dust in a place where it can not despezar with the passage of time, even recommends it in a bag and seal it after you throw it.
Clean all parts as you can with a damp cloth, so that the pieces do not stain the pages, and in this case it would not be for powder spill if not the parts are dirty, remember how it goes each piece and put back all instead.
If you can take pictures of everything much better process, it helps to remember where each piece goes.
This part we have to put in its place according to the signage, so avoid scratches on one end of the product in Brother printers, if necessary can verify the installation manual anyway going at one end which has a signaling.
They are independent printers cylinder unit to the toner cartridge, usually the cylinder of these printers can yield three toner cartridges before changing the cylinder with a new one.
With the passage of time and if we filled our toner several times we may begin to get a bad quality in our printed documents.
The symptom that more is when it is time for you to clean cylinder Brother printers are spots throughout the site, stains like if I opened fallen toner on the page, drops on all sides dust damaging the image of the document we want to print.
 |
| brother cylinder unit |
It may be the case that the unit cylinder is not damaged completely, if we see that the pages even the last to leave has good quality and filled our needs, then it is time to clean the cylinder and save the money we would need to buy a new cylinder.
Then a process for cleaning, may change in a few steps with the cylinder that you have but are very similar, so we need a little cleaning up, clip, pliers and screwdriver.
The cylinder has a very fragile surface is easily damaged and recommend to treat it with care and patience to avoid damaging any stripe is made in the cylinder will show on all pages to be printed on. Do not clean the drum unit with sun exposure, this is damaged without remedies.
First thing we do is loosen the toner drum unit, as mentioned above, the cylinder unit is independent Brother printers, we will release the toner off the drum to start cleaning.
 |
| cylinder unit separate unit toner |
We removed a grip that has the drive cylinder at one end, with this we seek the ease of removing the cylinder to expose the toner tank damaged.
The deposit tone damaged, is an amount of powder used to print that does not stick to the paper, this is called toner tank damaged because no use for reuse, as it passes to the deposition of damaged toner is mixed with pieces of paper and dust taken from the environment where the printer is if we again get very pale toner pages without quality.
 |
| remove handle to remove toner tank |
 |
| pull-through cylinder unit |
We removed everything very carefully checking where each piece goes, we voted dust in a place where it can not despezar with the passage of time, even recommends it in a bag and seal it after you throw it.
Clean all parts as you can with a damp cloth, so that the pieces do not stain the pages, and in this case it would not be for powder spill if not the parts are dirty, remember how it goes each piece and put back all instead.
If you can take pictures of everything much better process, it helps to remember where each piece goes.
 |
| cleaner thread |
COMMENTS